WORK PROCESS GAS UTILITY WORKER O*NET/SOC CODE: 49-9012.00 RAPIDS CODE: 0594 SKILL AREA APPROXIMATE HOURS A. SAFETY 350 1. Construction Site 2. Pit 3. Drivers Training B. CNG VEHICLE FUELING 50 C. PIPEFITTING AND PROCEDURES 350 1. Welded 2. Non-welded D. RADIO AND TELEPHONE OPERATIO AND TECHNIQUES 50 E. IDENTIFICATION, USE, CARE
Terrazzo Finisher
WORK PROCESS SCHEDULE TERRAZZO FINISHER O*NET-SOC CODE: 47-2053.00 RAPIDS CODE: 0972/0972HY This schedule is attached to and a part of these Standards for the above identified occupation. 1. TERM OF APPRENTICESHIP The term of the occupation shall be three (3) or four (4) years with an OJL attainment of a minimum of 3,900 or 5,200 hours
Carpenter, Interior Systems
WORK PROCESSES SCHEDULE CARPENTER, INTERIOR SYSTEMS O*NET/SOC CODE: 47-2031.01 RAPIDS CODE: 0653 The following schedule is an example of work experience (OJT) and training considered necessary to develop a skilled and productive worker in the Interior Systems trade. Within the limits of basic trade requirements, the schedule is adaptable to local conditions. APPROXIMATE HOURS General Knowledge
Painter (Any Industry)
WORK PROCESS SCHEDULE PAINTER O*NET-SOC CODE: 47-2141.00 RAPIDS CODE: 0379 This work process schedule is attached to and a part of the Apprenticeship Standards for the above identified occupation. This sequence of Related Classroom Instruction is competency based and will be offered as traditional classroom training or independent study, which may include electronic media. 1. TERM OF APPRENTICESHIP
Pavement, Stripper
WORK PROCESS PAVEMENT STRIPPER O*NET/SOC CODE: 47-2141.00 RAPIDS CODE: 1042 DESCRIPTION: Operates a variety of equipment to install thermoplastic and paint striping, stenciling, tape delineations, RAPIDSed pavement and traffic signs. Prepares the surfaces to be stripped. Reads and interprets blueprints to determine the scope and limits of the job, the phase to be performed, the nature of
Cable Television Installer
WORK PROCESSES CABLE TELEVISION INSTALLER O*NET/SOC CODE: 49-9051.00 RAPIDS CODE: 0566 Description: Install cable television cables and equipment on customer’s premise, using electrician’s tools and test equipment: Measures television signal strength at utility pole, using electronic test equipment. Computes impedance of wire from pole to house to determine additional resistance needed for reducing signal to desired level. Installs
Construction Craft Laborer (HY)
Work Process Schedule OCCUPATION Title: Construction Craft Laborer O*NET-SOC CODE: 47-2061.00 RAPIDS CODE: 0661HY This schedule is attached to and a part of these Standards for the above identified occupation. 1. TERM OF APPRENTICESHIP The term of the occupation shall be approximately two years with an OJL attainment of 4,000 – 5,100 hours supplemented by the required
Lathing Specialist
WORK PROCESSES LATHING SPECIALIST O*NET/SOC CODE: 47-2031.01 RAPIDS CODE: 0272 The following schedule is an example of work experience (OJT) and training considered necessary to develop a skilled and productive Lathing Ceiling Specialist in the Interior Systems trade. Within the limits of basic trade requirements, the schedule is adaptable to local conditions. Approximate Hours 1. General Knowledge
Line Maintenance
WORK PROCESS SCHEDULE HIGH VOLTAGE ELECTRICIAN (2801 TARGET 2810) LINE MAINTAINER O*NET-SOC CODE: 49-9051.00 RAPIDS CODE: 0283 This schedule is attached to and a part of these Standards for the above identified occupation. 1. TERM OF APPRENTICESHIP The term of the occupation shall be four (4) years with an OJL attainment of 8000 hours supplemented by the
Fabricator, Assembler, Metal Products
WORK PROCESS FABRICATOR-ASSEMBLER, METAL PRODUCTS O*NET/SOC CODE: 51-2041.01 RAPIDS CODE: 0833 DESCRIPTION: Fabricates and assembles metal products, such as window sashes, casements, doors, awning frames, shells, cases, and tubular products, such as golf carts or furniture, as specified by work orders, diagrams, and templates, using handtools, power tools, and metalworking machinery: Lays out and marks reference points onto
